How to take apart a gameboy advance sp

how to take apart a gameboy advance sp

How to Replace the Housing of Your GBA SP

May 17,  · First take the battery cover and battery out and set them aside (sorry for the bad pics): There are six Tri-wing screws here – one is in the battery area, but because of the flash you can’t see it, sorry. Take all six out and the bottom cover should come off easily; be careful of the power switch slider – it might come off. This video shows you how to safely take apart your (hopefully) Game Boy Advance SP. This is part one of two, so stay tuned for more! This video shows you how to safely take apart your.

First, you need a small Philips screwdriver, a tri-wing screwdriver or a 1. OK — right in to it. First take the battery cover and battery out and set them aside sorry for the bad pics :. Take all six out and the bottom cover should come off easily; be careful of the power switch slider — it might come off.

There is also a square nut that is used to hold the battery cover down — it might have fallen off the board or it might still what kind of fool lyrics gary allan in the bottom cover. On the board there are three Philips screws holding it in; just unscrew them and the board should come up a little. There is a connector that the LCD Ribbon cable plugs into — the brown part of the plug is a lock.

Undo that and the connector should slide out easily. After the board is removed, you will see the buttons. They might have the rubber push pads on them see pic above on the board.

Take them out and set them aside. The speaker also comes out; there will be a black paper thing underneath the speaker — take it out also. This will open part of the hinge area and allow you to remove the ribbon cable:. The Screen and upper part of the case is held in by five tri-wings located under the white rubber pads.

After you take the screws out, the case will come apart and the screen will fall out, as it is just held in sandwiched between the front and back part of the case. Carefully maneuver the ribbon cable out of the hinge area and set the screen aside. The left and right buttons, in the bottom part of the case, are held in by springs — care should be taken to not lose the springs. Note that the power switch slider the part with the curve in it goes in the bottom part of the case.

I originally took it apart to paint it:. The platinum version of the SP was painted and the paint was very thin and scratched easy after getting a bunch of scratches from normal use.

I decided to paint it. Curtis Lafferty. It runs at either 1 GHz or 1. Why should you care? Save my name, email, and website in this browser for the next time I comment. News Ticker. Next Four Years. April 5, admin Uncategorized 0. November 17, admin How to make individual cupcakes 0.

September 12, admin Uncategorized 0. Discussion Leave a Reply Cancel reply Your email address will not be published. We use cookies to ensure that our site performs its best for you. By continuing to use this site we will assume you accept our Privacy Policy.

Step 1: ?Removing the Old Housing

Apr 30,  · Informative and slightly comical. Feb 10,  · Use the spudger to lift the screen from the front panel. Place the spudger in the space directly left of the D-pad. The screen and the front panel is connected by a black tape that could rip if not removed carefully. You can use an iOpener or a hair dryer on the other side of the front panel in order to soften the black tape. Fun video about taking apart and painting a GBA SP. Some nice Nintendo, mario, tetris, gameboy chiptunes in the background. I find a lot of GBA SP models on.

This teardown is not a repair guide. To repair your Game Boy Advance, use our service manual. Remove the back panel by pulling away with one hand and the front secured in the other hand. Beware of right and left triggers, the right and left panels, and the power switch falling off as the back panel is removed. For finicky or jammed triggers only.

Adjust and correct triggers and reassemble. Most jammed triggers are caused by buttons misplaced or jammed in its enclosure. Replace with another switch if necessary. Pull circuit board away from the front panel by pulling up at the bottom of the circuit board, keeping the top ribbon still connected.

Remove the plastic buttons and the D-pad from beneath the rubber pads with tweezers or by hand. Once the LCD ribbon port has been unlatched, the LCD ribbon should very easily slide out and can be removed with zero force using fingers or tweezers. Use the spudger to lift the screen from the front panel.

Place the spudger in the space directly left of the D-pad. The screen and the front panel is connected by a black tape that could rip if not removed carefully. You can use an iOpener or a hair dryer on the other side of the front panel in order to soften the black tape. Badges: I dont understand. Fix Your Stuff. Published: February 10, Tools Featured in this Teardown. Introduction Use this guide to disassemble all or any of the parts of the Game Boy Advance. Step 1 Game Boy Advance Teardown.

Add a comment. Add Comment Cancel. Step 2. Step 3. Step 4. Step 5. Step 6. Step 7. Step 8. Step 9. Step One comment. Author with 10 other contributors. Bruh thx for. Great guide. Single Step Full Guide. Small - px Medium - px Large - px. View Statistics:.

Comments:
There are no comments on this entry....